Page 1 of 1
Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 02 Nov 2016, 13:24
by WeatherWatcher
Ok I need to drill a hole in my car roof to fit a mount for my dualband antenna. Have found nothing in the way like ribs or wiring under the head lining but now need to purchase a drill bit 16mm dia for the one hole- what would people recommend?
Because it is almost centre of the roof longitudanally should be OK. I know about the getting a good earth bit and cleaning any burrs off the edge of the hole. Any other advice welcome.
Re: Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 02 Nov 2016, 14:03
by MrWeetabix
16mm seems big.... double check that fella!
Re: Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 02 Nov 2016, 14:06
by WeatherWatcher
SO 239 mount. Will get mount first and then sort out drill when confirmed size.
Re: Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 02 Nov 2016, 14:12
by 26TM931
Oldman54 wrote:SO 239 mount. Will get mount first and then sort out drill when confirmed size.
you have a pm
Re: Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 02 Nov 2016, 15:02
by dt307
here you go
Re: Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 02 Nov 2016, 15:34
by Dragonfly
If you have this type i think they need a 12mm DV connector hole
http://www.thunderpole.co.uk/fixed-body ... t-kit.html
Check u have around 35mm space between head lining and roof .
Re: Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 02 Nov 2016, 15:50
by WeatherWatcher
Thanks Dragonfly that is the mount I intend to use, getting it with mini 8 coax cable from
http://www.4x4cb.com/ who are not too far away from me- local enough to arrange a pick up to save on carriage( tight wad that I am).
Re: Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 02 Nov 2016, 17:18
by thedeerhunter270
Re: Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 02 Nov 2016, 18:32
by stanogs68
just hammer a six inch nail through it ,but use good heavy lump hammer to get it through with one all mighty smack
Re: Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 03 Nov 2016, 16:16
by porky.69
stanogs68 wrote:just hammer a six inch nail through it ,but use good heavy lump hammer to get it through with one all mighty smack
pmsl
Re: Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 03 Nov 2016, 22:39
by vx900
Re: Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 04 Nov 2016, 08:23
by VintageTin
Q-max would be my preference, assuming a very low crown panel as, by the very nature of the way it works, it could locally distort any curved panel.
An ideal way of cutting accurate, clean, holes.
Re: Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 04 Nov 2016, 15:32
by sec1223
stepped drill bit.. best idea
Re: Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 30 Nov 2023, 23:26
by ke7azd
Place duct tape over the head liner so it doesn't bunch up and rip / shred. I used these drill bits.
73's
Re: Advice on Best Drill to use to drill hole for SO239 mount.
Posted: 03 Dec 2023, 12:06
by grafter
When I did this to my Landrover I found the roof panel to be too flexible so added a sheet of aluminium underneath large enough to tuck under the nearest support rib that ran over the roof. This meant sourcing an SO239 mount that had a longer threaded section.