+10kc jump for stalker9
- dt307
- Top Poster
- Posts: 1250
- Joined: 05 Sep 2014, 16:15
- Call Sign: 163dt307
+10kc jump for stalker9
desolder pin 9 on ic5(9dx)or ic301(9fdx)
you can isolate pin 9 but cutting the track but i never cut tracks unless no other way can be found.
this is the way i do it and i have not seen it done like this
please make sure the pin 9 is desoldered properly before you continue.
insert a small flat screwdriver between pin 10 and behind pin 9 and prize it out note...the pin will come out very easy if ANY resistance is felt STOP and desolder it correctly.
connections
straighten pin 9 a little so it protrudes at roughly 90 degrees and solder a white wire to this pin (check your work and slide some heat shrinking over the joint)
remove the retaining screws for the font pannel to give you room enough to work.(9fdx) as the ic301 is located on the channel selector boardyou can isolate pin 9 but cutting the track but i never cut tracks unless no other way can be found.
this is the way i do it and i have not seen it done like this
please make sure the pin 9 is desoldered properly before you continue.
insert a small flat screwdriver between pin 10 and behind pin 9 and prize it out note...the pin will come out very easy if ANY resistance is felt STOP and desolder it correctly.
connections
straighten pin 9 a little so it protrudes at roughly 90 degrees and solder a white wire to this pin (check your work and slide some heat shrinking over the joint)
You do not have the required permissions to view the files attached to this post.
163dt307-chris
“I fear the day that technology will surpass our human interaction. The world will have a generation of idiots.”
― Albert Einstein
“I fear the day that technology will surpass our human interaction. The world will have a generation of idiots.”
― Albert Einstein
- dt307
- Top Poster
- Posts: 1250
- Joined: 05 Sep 2014, 16:15
- Call Sign: 163dt307
Re: +10kc jump for stalker9
solder a black wire into the hole that pin 9 was in
first we need to disconect the nb/anl and make it constant in the on position.
solder a red wire WITH A 1K RESISTOR IN SERIES to constant +8v on front of pcb right by the swith or (pin 16 of either of the 4008 adders will do ic5/6 (9dx) ic301/302(fdx))
you can wire the three wires to any switch wack a hole in the back ect and be as rough as you like but i will use the nb/anl (if you do want to fine but at least for the love of god find a ground and +8v constant near the switch and dont run three wires all the way from the back to the front)first we need to disconect the nb/anl and make it constant in the on position.
You do not have the required permissions to view the files attached to this post.
163dt307-chris
“I fear the day that technology will surpass our human interaction. The world will have a generation of idiots.”
― Albert Einstein
“I fear the day that technology will surpass our human interaction. The world will have a generation of idiots.”
― Albert Einstein
- dt307
- Top Poster
- Posts: 1250
- Joined: 05 Sep 2014, 16:15
- Call Sign: 163dt307
Re: +10kc jump for stalker9
there is two halves to the switch 6 pins 3 left 3 right
on the left side (on this one) the upper pin is not used remove the two wires and add some heat shrink to stop them shorting on anything as they are not needed on the right side the lower pin is not used remove the two wires and solder them together and heat shrink them up wire the nb/anl switch as follows any side will do
lower pin black
middle pin white
top pin red
yep you getting the idea add some heat shrink keep it tidy
on the left side (on this one) the upper pin is not used remove the two wires and add some heat shrink to stop them shorting on anything as they are not needed on the right side the lower pin is not used remove the two wires and solder them together and heat shrink them up wire the nb/anl switch as follows any side will do
lower pin black
middle pin white
top pin red
yep you getting the idea add some heat shrink keep it tidy
You do not have the required permissions to view the files attached to this post.
163dt307-chris
“I fear the day that technology will surpass our human interaction. The world will have a generation of idiots.”
― Albert Einstein
“I fear the day that technology will surpass our human interaction. The world will have a generation of idiots.”
― Albert Einstein
- dt307
- Top Poster
- Posts: 1250
- Joined: 05 Sep 2014, 16:15
- Call Sign: 163dt307
Re: +10kc jump for stalker9
the way i do it you can turn the radio back standard easy and no one will know you been in there
or if you dont want to do it that way you can cut two tracks on pin9 then solder the white wire to pin 9 cut where tweezers are pointing then you must add a jumper to restore the ground you cut to the rest of the circuit add the black wire to a ground
takes me 10-15 mins to do the mod my way but i have done a fair few
there is no right or wrong way to do this or any mod or do i think its better or worse than any i seen
i have no worries in selling a radio after doing this mod its clean,tidy,works,and can be totaly reversed and nothing gets hacked up
pic of the solder after finished
JOB DONE
or if you dont want to do it that way you can cut two tracks on pin9 then solder the white wire to pin 9 cut where tweezers are pointing then you must add a jumper to restore the ground you cut to the rest of the circuit add the black wire to a ground
takes me 10-15 mins to do the mod my way but i have done a fair few
there is no right or wrong way to do this or any mod or do i think its better or worse than any i seen
i have no worries in selling a radio after doing this mod its clean,tidy,works,and can be totaly reversed and nothing gets hacked up
pic of the solder after finished
JOB DONE
You do not have the required permissions to view the files attached to this post.
163dt307-chris
“I fear the day that technology will surpass our human interaction. The world will have a generation of idiots.”
― Albert Einstein
“I fear the day that technology will surpass our human interaction. The world will have a generation of idiots.”
― Albert Einstein
-
- Super Member
- Posts: 231
- Joined: 13 Mar 2015, 19:28
- Call Sign: 163TM2803
- Location: Cwmbran, South Wales.
Re: +10kc jump for stalker9
Thanks Chris for taking the time. The instructions are great and laid out in an excellent format (i applaud you).dt307 wrote:the way i do it you can turn the radio back standard easy and no one will know you been in there
or if you dont want to do it that way you can cut two tracks on pin9 then solder the white wire to pin 9 cut where tweezers are pointingIMG_0198.JPG
then you must add a jumper to restore the ground you cut to the rest of the circuit IMG_0199.JPG
add the black wire to a ground
takes me 10-15 mins to do the mod my way but i have done a fair few
there is no right or wrong way to do this or any mod or do i think its better or worse than any i seen
i have no worries in selling a radio after doing this mod its clean,tidy,works,and can be totaly reversed and nothing gets hacked up
pic of the solder after finished IMG_0200.JPG
JOB DONE
Pics are excellent and very clear. Im sure if you printed all your work off into a booklet form you would have a lot of people wanting this booklet im sure.
Going to give it a go tonight let you know how i get on. Thanks Greatly.
Last edited by tony2803 on 20 Feb 2017, 11:26, edited 1 time in total.
- dt307
- Top Poster
- Posts: 1250
- Joined: 05 Sep 2014, 16:15
- Call Sign: 163dt307
Re: +10kc jump for stalker9
no worries i am off today no work but got a stalker,two hy-gains and an adams i want to sink my teeth into so i will be about all day so
if your not sure on anything post here BEFORE no need to guess anything as your board is the other type and i will answer any questions as you go
m8
if your not sure on anything post here BEFORE no need to guess anything as your board is the other type and i will answer any questions as you go
m8
163dt307-chris
“I fear the day that technology will surpass our human interaction. The world will have a generation of idiots.”
― Albert Einstein
“I fear the day that technology will surpass our human interaction. The world will have a generation of idiots.”
― Albert Einstein
- Tripple 7
- Regular
- Posts: 57
- Joined: 13 Mar 2016, 04:34
- Call Sign: 777
Re: +10kc jump for stalker9
Thanks a lot Chris for taking your time to put this excellent modification in public for sure it's a great idea to publish pictures the way you did it my congratulations
- 14CS06
- Top Poster
- Posts: 1796
- Joined: 04 Mar 2012, 09:15
- Location: JN33LN - ALPES-MARITIMES-06 France
Re: +10kc jump for stalker9
Hello Chris
Many thanks
Very good post
@+
Claude
Many thanks
Very good post
@+
Claude
Photo Collector CB RADIO
- Raverrst
- Super Member
- Posts: 115
- Joined: 18 Mar 2018, 18:15
- Call Sign: 26LW29
- Location: Devon
Re: +10kc jump for stalker9
Hi..
Newbie here, joined yesterday, carried out this mod this evening, works brilliantly Excellent post, very easy to follow..
Now is there a similar thread or any brainy peeps that can shed some light on getting the clarify to swing 5kc either side of twelve o clock so I can get on to the zeros to listen at least..
Newbie here, joined yesterday, carried out this mod this evening, works brilliantly Excellent post, very easy to follow..
Now is there a similar thread or any brainy peeps that can shed some light on getting the clarify to swing 5kc either side of twelve o clock so I can get on to the zeros to listen at least..
Radios, radio!!
- cb4ever104
- Legend
- Posts: 6561
- Joined: 28 Jul 2011, 21:26
- Location: España
Re: +10kc jump for stalker9
The only thing I'd add is that I normally add a 1k resistor to the wire that goes to pin 9 of the pll .
30TM060
Paul aka "Sammy". (108) PY60 Old Paisley DX Group (RIP Rab Markie)
Ex GM0 , now EA5 .
Handle "Fortune Hunter" back in "the day"
Radios ....? Anything that says "TAIWAN R.O.C" on the back.
Paul aka "Sammy". (108) PY60 Old Paisley DX Group (RIP Rab Markie)
Ex GM0 , now EA5 .
Handle "Fortune Hunter" back in "the day"
Radios ....? Anything that says "TAIWAN R.O.C" on the back.
- Raverrst
- Super Member
- Posts: 115
- Joined: 18 Mar 2018, 18:15
- Call Sign: 26LW29
- Location: Devon
Re: +10kc jump for stalker9
Forgive my lack of knowledge cb4ever104, What reason would you fit a 1k resistor? safety?cb4ever104 wrote: ↑20 Mar 2018, 11:16 The only thing I'd add is that I normally add a 1k resistor to the wire that goes to pin 9 of the pll .
Radios, radio!!
- cb4ever104
- Legend
- Posts: 6561
- Joined: 28 Jul 2011, 21:26
- Location: España
Re: +10kc jump for stalker9
Hi . yeah . Just to protect . I don't like connecting +VCC wires directly .
Sammy
Sammy
Last edited by cb4ever104 on 21 Mar 2018, 12:42, edited 1 time in total.
30TM060
Paul aka "Sammy". (108) PY60 Old Paisley DX Group (RIP Rab Markie)
Ex GM0 , now EA5 .
Handle "Fortune Hunter" back in "the day"
Radios ....? Anything that says "TAIWAN R.O.C" on the back.
Paul aka "Sammy". (108) PY60 Old Paisley DX Group (RIP Rab Markie)
Ex GM0 , now EA5 .
Handle "Fortune Hunter" back in "the day"
Radios ....? Anything that says "TAIWAN R.O.C" on the back.
- dt307
- Top Poster
- Posts: 1250
- Joined: 05 Sep 2014, 16:15
- Call Sign: 163dt307
Re: +10kc jump for stalker9
sammy,s resistor wont hurt things and add a level of protection
protecting the +8v line from shorting out is an idea as well
if the switch should fail and the internal contacts get messed up there is a possibility the +8v line would be shorted to deck and do some damage to the regulator circuit (rare chance but possible)adding a resistor in series between the +8v line and the switch would be fine in this instance as well.
will update the post thanks sammy nice to see you m8
protecting the +8v line from shorting out is an idea as well
if the switch should fail and the internal contacts get messed up there is a possibility the +8v line would be shorted to deck and do some damage to the regulator circuit (rare chance but possible)adding a resistor in series between the +8v line and the switch would be fine in this instance as well.
will update the post thanks sammy nice to see you m8
163dt307-chris
“I fear the day that technology will surpass our human interaction. The world will have a generation of idiots.”
― Albert Einstein
“I fear the day that technology will surpass our human interaction. The world will have a generation of idiots.”
― Albert Einstein
- dt307
- Top Poster
- Posts: 1250
- Joined: 05 Sep 2014, 16:15
- Call Sign: 163dt307
Re: +10kc jump for stalker9
CAN A MOD EDIT THIS PLEASE AS I CANT!
solder a red wire WITH A 1K RESISTOR IN SERIES to constant +8v on front of pcb right by the swith or (pin 16 of either of the 4008 adders will do ic5/6 (9dx) ic301/302(fdx))
THANKS
solder a red wire WITH A 1K RESISTOR IN SERIES to constant +8v on front of pcb right by the swith or (pin 16 of either of the 4008 adders will do ic5/6 (9dx) ic301/302(fdx))
THANKS
163dt307-chris
“I fear the day that technology will surpass our human interaction. The world will have a generation of idiots.”
― Albert Einstein
“I fear the day that technology will surpass our human interaction. The world will have a generation of idiots.”
― Albert Einstein
- Raverrst
- Super Member
- Posts: 115
- Joined: 18 Mar 2018, 18:15
- Call Sign: 26LW29
- Location: Devon